Part 3:

This will be a “short post” since we have had a third machine to add to our investigation (which I hope will continue on next Monday).  Ann has received a package from Georgia, hopefully containing the Solar Bee she ordered. It is vary similar to the design of handle and motor placement of the Orange fly but instead of a single needle it can have up to 4 needles. We will let you know what we find out about it soon.

The continuing investigation into the first 2 electric felting machines (China and Ukraine)

A quick look at trying detail work on pre-felt:

I tried fine detail work on pre-felt with merino, first with the Orange Fly (Ukraine). I did not have trouble working along the edge of main branches but found that it felted much faster than I am use to. the increased speed of felting is especially noticeable when we tried felting the tiny branches. Although it worked well, I did not feel as confident in my control of wool moving, I suspect I just need more practice.

 1- dry felting on dry pre-felt.

Next I wanted to try a piece of pre-felt that had been wet felted by Ann. This was one of her tree prototypes that she did not use as her finished tree.

2-3 pre-felt with one of Ann’s wet felting tree tries.

   4-6  I wanted to try adding little cardinals (red birds) to the tree.

I found that the machine grabbed the fiber and pushed it with enthusiasm into the pre-felt. A bit more than I had expected.  Again I think more practice would improve the bird-ish-ness of my red blobs!

7 the back of the pre-felt showing the red fibers pushed to the back.

 I also tried on the orange Fly on 2 more wet felted bases with good results and not as good results.

Our next test base was a felt Ann had made in two colours of brown.

It was about the thickness for a wet felted hat but could be a good surface for a picture.

The single needle of the orange fly did not have trouble embedding fiber into the felt.

8-11 working on solid wool felt.

I found that I felt more fiber movement when I angled the needle insertion. This would allow more barbs to engage fiber without having to imbed the needle into the wool felting mat.  (Angling the needle reduces the depth of insertion while still allowing more barbs to grab and entangle fiber.)

Having only one needle should be slower when laying in a general background colour. But, it is still quite quick, and there was no stress on my wrists, fingers, elbow or shoulder.  Ann and I should try a race between the felting machines vs. the 10 needle bar tool, which I find very fast for laying in backgrounds. But speed is not the only factor that the machines address.

We also considered the mettle machine from china. As you remember the mettle machine did not like most of the felting surfaces as much as the orange fly did. We used the fake clover brush (driveway asphalt painting bush from the hardware store) which is what seemed to be its favorite surface so far in our investigations.

 12 Mettle machine felting into wet felted wool on the driveway brush

Wet felted (Fulled) knitting as a felting surface.

Ann had fulled a piece of knit sweater and brought a piece to try felting into. the orange fly did transfer the white fiber through the knitting successfully but it was a bit more resistant than the firm felt.  (It is quite firmly fulled knitting.)

 13-14 Orange Fly felting fulled wool knitting on a wool pad

Next I tried the mettle machine on the same surface. I noticed one of the screws loosening so stopped and tightened it. I suspect that you may want to check all the screws occasionally just so you do not lose one.

  15-16  mettle machine felting into fulled sweater on wool mat, one of the tiny screws had started to loosen.

There is less resistance when using the driveway brush  as a work pad but there was still the most resistance when we were felting on the fulled sweeter. Running with 2 needles was also less resistance than running the machine with 4.

  17-19 checking work angle and comfort holding mettle machine

I again tried holding the machine vertically and on an angle.  Both were comfortable to hold and there was less vibration/resistance when using the brush with this machine.

I have been making a chart for the 3 machines so next we will investigate the machine from Georgia and fill in the rest of the chart. We will open the package and put it through its paces next Monday (which is a holiday) and hope to have some test results ready for the next blog post!

For working on wet felting the orange fly seems to be a bit more enthusiastic towards embedding fiber into the felt/fulled 2D picture ground .  I will not give up on the mettle machine, I suspect we have not found its forte yet. I want to look further at 3-D sculpture. i am a bit concerned with the machines hitting armature wires (I may have to find some safety goggles before I try that!)

Until we can find out what’s in Ann’s mysterious package, Have fun and keep felting!

20 the mysterious package arrives at Ann’s