Browsed by
Tag: stitched tea bag leaves

Five leaves made from painted tea bags and free motion machine stitching that have been burnt with a soldering iron.
Creating a Branch, Leaves and Lichen for a Felt Tree Trunk

Creating a Branch, Leaves and Lichen for a Felt Tree Trunk

Comments 20 comments

In my last post, I showed you the beginnings of a tree trunk that I have been creating. Next up was to make a branch, leaves and lichen for the trunk.

Felted fringe cut from a scarf above felt tree branch made from similar fringe.

The branch was made from the fringe that I cut off when I felted the tree trunk. There is extra fringe at the top of the photo above and the branch that I created from a similar piece of scarf below. I did a bit of twisting, tacking it down with a felting needle and then wet felted the branch.

Interfacing and nylon organza painted purple.

I painted some lightweight interfacing and some nylon organza to make the lichen. It was fun to make lichen in purple!

Here’s the set up that I use for burning synthetic fabric. It gives off bad odors so I put a piece of glass on my stovetop, turn on the fan in the vent hood and burn with a soldering iron first. Once I get the shapes, then I use a heat gun to further shrink and change the shape of the fabric. It shrinks the fabric down, so you need to burn out more pieces than you think you need. (Make sure to be very careful with the soldering iron and keep it away from your fingertips. You also might want to wear a mask.)

Here’s the burnt interfacing on the left and the result after heating with the heat gun on the right. I usually tear these pieces up into smaller sections as that looks more like the way lichen grows on tree trunks. Do you like the little dog at the bottom? Totally unplanned.

Here’s the nylon organza. I do both the interfacing and the organza because they each give a different texture. That way when mixed together, it looks more like real lichen.

Next up was to create the leaves. I used tea bag papers that I painted. I wanted a soft peach-pink color but ended up with more of an orange color. Oh well, I kept going. The top right shows the tea bag papers layered with two papers and then free motion machine stitched to make veins. Then I cut out the leaves to the correct shape and then used a soldering iron to burn bits away and make little holes. Now they look like fall leaves.

But I was still unhappy with the color. I definitely wanted them less orange and more pink. So I took some leftover tea bag paper and tried several different media to see what I liked best. I ended up using the pink colored pencil. Now to stitch it all together and see if it needs anything else, but you will have to wait until June for that post.

 

Felt and Stitched Moss on Driftwood with Close Up of Tea Bag Leaves
Adding Dried Leaves to Mossy Driftwood

Adding Dried Leaves to Mossy Driftwood

Comments 22 comments

I have been continuing to add more stitching and other bits to my mossy driftwood. You can see the progression from just felt to adding stitch in these two posts:

Moss on a Piece of Driftwood

Mossy Driftwood Continued

Driftwood covered with green felt and hand and machine stitched areas of moss.

The moss has been getting filled in by hand stitching and adding the machine stitched moss I created. I am trying to decide how much more hand stitched moss to add. I think it needs more “trailing” knots in the “bare” felted areas. But I also need to add lichen in places but I haven’t created the lichen yet. I’m thinking I will try Tyvek lichen.

Leaf shapes created out of tea bags and machine stitching.

The next step was to create dead, desiccated leaves. I found a tutorial for making them out of tea leaves on Youtube.  I had made them out of Lutradur before but not tea bags so I thought I would give it a go. I drink tea every morning so I started saving the old tea bags for this project. In the video, she used some type of stabilizer but I decided to try without one. I layered two flattened tea bags together and just started free motion machine stitching the veins. As you can see, you don’t want to stitch the outer edge of the leaf as it looks more natural without it. Then I cut them to shape with scissors.

Tea bag leaves, machine stitched veins and burned holes/edges.

The next step was to burn the edges and the holes. I found it was easier to get a more natural look when I was looking at photos of dead leaves. That way the leaves don’t all turn out the same. I used a wood burning tool for this operation (the video uses an incense stick). Obviously, you need to be careful when you’re burning things and it is pretty stinky too, you need ventilation. So I took mine to the stove and turned on the overhead fan to draw away the fumes. Plus the stove top is heat proof and won’t be burned or damaged.

Fiber art moss on piece of driftwood with three tea bag dead leaves.

So here’s the full piece with the leaves just placed on it. I will be stitching them down at some point to hold them in place.

Here’s a couple of close ups. You can click on the photos for a bigger view. I am happy with the progress and it is definitely looking very “forest floor”.