Browsed by
Tag: felt pot

Pot Inside a Pot 2

Pot Inside a Pot 2

It was 2 days later that I got back to my pot. After some preliminary rolling in the dryer, I rolled it by hand.

It shrank quite a lot. it is very tight around the resist.  It is time to do some cutting. I cut in the spaces between the fins.

You can see how much the hole grows as you work the edge. The little blob on the left is the piece I cut out.

I didn’t want to pull the resist out through the hole. It is bulkier and less flexible than usual with the duct tape holding on the fins. I cut an X in the bottom of the outside pot. If I had thought about it I would have done it in the bottom of the inside pot so no one would ever have seen it.

This is how much it has shrunk so far.

Next was a vigorous rub down with a rubbing tool. This is one Jan found in the pet section of our Dollar store. It’s for washing your very dirty dog. I covered the pot with some plastic before rubbing. It is too grabby to use directly on the felt.

l

It shrank a little more but now it is al flat and smooth.

Before doing any more I needed to rinse out the soap. It always takes much longer to get all the soap out than I think it should.

I start with hot water and finish with cold. I also want to get more shrinkage during this prosses so I am quite aggressive in getting the water through felt to get the soap out.

This is how much more it shrank. You can see the black lines of where it was before rinsing.

I stuck the yellow inside the red one. It wasn’t too hard because the how where they are joined is not very small.  What was harder was getting the ball in so I could blow it up. I wanted to use a ball because I didn’t think a balloon would be strong enough. I did get this one I but ended up taking it out and switching to a smaller 8-inch ball. the ball is a Linsom ball, they are nonslip, sort of sticky on the outside. They are great balls because they come with a removable plug. I took a vessel class with  Sharon Costello where we used them. I suppose it helped the first layer of wool to stick.  The layout on a ball is very difficult. It was a great class, a lot of fun and we learned a lot but not one I like to use.

and in the dark

I think it turned out fairly well. If I were to do it again I think I would make the inside pot bigger so it would open up the fins. I may, depending on how ambitious I am, wet it down, blow up a ball inside and them stuff plastic bags in to make the outer pot bigger. I may cut the fins off and then so some stretching so you can see more of the inside pot. I am still thinking. What would you do?

Little Pot is Finished

Little Pot is Finished

As promised here is the finished pot. It did work, as if there was any doubt.  All the problems I had were to do with the size of the pot and me.

The first problem is that I cut the whole in the top much to big. I think it would have been better pot if it had curved in at the top. it is much to open making it more up and down. Part of that is the size of the piece. It is only about 2.5 inches tall. Also I should have to cut the holes sooner  so I can work on the cut edges, or at the end so the edges would be cleaner.

Here are the silk cocoons I put in. I did not position these well so on is to high and one to low. Again the size of the pot limited my options.  The cocoons did work well. They were crushed., but that didn’t really matter. After it was dry I cut open the cocoons and then steamed them to reshape them.  It may have been better to do those sooner so m=perhaps the cut holes could have been made smoother. All in all not a great pot but it  was a good piece to remind me of all thing I really already new but didn’t think about.  I think I will make another one but bigger.

 

Felt Vessel Class

Felt Vessel Class

I taught an enthusiastic group of ladies how to make felted vessels last Sunday. They were a great group and without Carleen’s reminders to take pictures I would have nothing to show you today.

This slideshow requires JavaScript.

Three ladies chose to make pots that were a different colour inside.  and two made theirs a solid colour.

Then of course there was the wetting, rubbing and rolling and shaping

   

    

 

Blowing up a balloon inside  helps get a nice shape. In the back ground you can see Carlene rolling on a car mat.

For some reason I did not get a picture of all the finished pieces. This is the only one I have of this white and gold pot. It was very elegant and I think it would make a great light cover. She said she was rewetting it and reshaping it. I hope she remembers to send me a picture of it when it’s done.

There was also some very determined rolling on the glass wash board.

I do have some finished pictures.

 

The blue one is Carlene’s. She wants to add to it. Here are 3 thoughts. The second and third pictures are the same yarn but different ends,  one has more blue in it.

Her husband thinks the yarn covers up to much of the pot. I like the spiral but think maybe make the lines farther apart. What do you think? It may have been better to felt it right in. It would still be texture but flatter, more integral to the pot. Hey Carlene, maybe you just need to make another pot.

%d