Imbolc heralds the start of spring in the Celtic calendar.  In recent years, a bank holiday has been established in Ireland to celebrate it.  It is known as St Bridget’s Day and it is celebrated around 1st February.  Before Christianity hit Ireland St. Bridget was the Celtic Goddess Brigid and like most females she was a real multi-tasker when it came to her role in mythology.  If you would like to find out more about Imbolc here is a link to a good read on Wikipedia.

Seeing as how spring has supposedly sprung here (although personally I would question that given the amount of rainfall we are experiencing), the daffodils are making an appearance so I am writing this with a sense of renewed energy for the longer days ahead.  I thought it might be nice to share my process from a recent little project I did.  It was more out of curiousity than need that I did this.  The focus is on differential shrinkage.  You will not need a lot of fibre for this – you should have plenty left over if you set aside 15g.  I used merino.  I also used some felt ‘ribbon’ that I bought before Christmas from DHG Italy  But you don’t actually need to buy this.  You could as an alternative make up a rectangle of prefelt – lay down 4 layers for this as I have doubled up on the ribbon (each layer of the industrial prefelt ribbon is equivalent to 2 layers of fibre) then you could cut the prefelt into strips arouond 1cm wide.

You will also need your usual felting equipment and a few extra bits.  I used decorator’s plastic (the really light plastic to protect the ribbons as I was felting them down.  I also used underfloor laminate for my resist but you can use whatever you normally use for this.  I am fortunate that I have some lovely wooden tools to help me with shaping but these are not essential as working the piece with your hands will also do.  So now, I am going to take you through the making process:

First of all, I prepared my resist, this is oval shaped and measure 38cm at the longest part by approximately 24cm on the fattest.  This was covered with 2 layers of fibre on each side – each layer will be perependicular to the other. 

After this, I spiralled the ribbon prefelt around the oval. I tried to keep the blue spaces between as even as possible but it was not something I fretted about. Because the ribbon was only 2 layers I repeated the process. So I ended up with 2 layers of the blue on the main body of the resist and 6 layers of the blue/red on the parts that I wanted to highlight. I added my net, a little more soapy water and after a little gentle rubbing I covered the surface in the light decorator’s plastic. I made sure that this was air tight as then there would be less likelihood of the added layers moving as I felted it. I added extra soapy water to the top of the plastic so that my hands would slide easily over the surface. A little extra attention was paid when rubbing; to the sides so that the fibres stayed snug with the side of the resist and to the added layers. Then I started some light rolling. I did 100 rolls along the north/east/south and west of the piece, flipped it over and did the same on the other side. (800 in total) I kept at this until it was well prefelted and had started to shrink:

At this point, I cut a small hole in the piece. I immediately set about sealing the hole by rubbing the edge so that the fibres would not contract and make the hole bigger. This was important as I wanted to sew the hole up again after I took out the resist. Once this was done, I used nylon thread to sew up the gash. Nylon thread will not felt in to the work so the stitches can be removed afterwards.

I want to show you all the bits and pieces at this point. You can see how much the felt has shrunk already when compared to the resist. You can also see three felting tools which I am using to work the piece and direct the shrinkage. The ball like one I found on a wood turners stall at a show. I wanted to buy it from him but he could not sell it to me so he generously donated it to the cause! The unusually multiangular shaped tool is most cherished as it was a gift from a friend who had travelled to Japan. ‘The third, more pointed one I purchased from a friend who is based in Germany.

Then I got down to the job of some serious fulling and shaping. Lots of rolling and rubbing with the well soaped tools happened at this stage. It would also be possible to do this stage with your fingers but it might be fun to see what you have around the kitchen that could also work. Here are a few photos of the work in progress:

Of the many joys felting brings into my life, I simply love the stage in the process where the wool begins to act like clay and starts moulds to my will and desires. These are always happy moments and they make what can often be lots of hard work seem very much worthwhile. Once I removed the nylon thread, I continued on to the final shaping and drying. And here is the final result from a variety of angles:

I may continue to play with the shape a bit more when I have time. I have since made a bigger version where I doubled the size of the original oval and used a different breed of fibre. This piece was made with a natural cream coloured fibre and I have to say I prefer the two colours as it highlights the spiral shape better. That said, I enjoyed my explorations into differential shrinkage.

I hope that this post will tempt you to try some differential shrinking. If you decide that this project is for you, please let me know. Better still, show me your results and let me know what tools (if any) that you have discovered around the house to help you with shaping.

Happy felting to all!

Helene x

Upcoming workshops:

I currently have two on-line workshops on offer through the Felting and Fibre Studio College of Fiber and Arts. The 3D felted pod is available all year round so you can apply to join it anytime. The workshop is recorded in real time so you can work alongside the videos. There are also PDFs that fully follow the video recordings. I am also available in the virtual classroom should students want to ask any questions or share their beautiful creations. Here is a link to further information on the course: https://feltingandfiberstudio.com/classes/online-course-wet-felting-a-vessel-using-a-simple-resist/

Registration opens on 13th March for my Wet Felted Hanging Spiral course. The course will start on 27th March and will run until 24th April. If you would like to find out more about this course, please head over to the page at https://feltingandfiberstudio.com/classes/hanging-felted-spiral/.

Here are some photos of students’ beautiful work from past courses: